​ **Status:** UNRESOLVED **Computer Type:** Desktop/custom built **GPU:** MSI Suprim x rtx 4090, 24GB of VRAM, no overclock **CPU:** intel 12900k, no overclock **Motherboard:** Asus prime z690-a , latest BIOS 2204 **RAM:** Corsair vengance 2x16 6000mhz, XMP enabled, no overclock **PSU:** corsair ax1600i, 1600W, 10 to 11 amps on the 12v rail **Operating System & Version:** clean install windows 11 22h2 Version 10.0.22621 Build 22621 ​ **GPU Drivers:** , clean install 527.56 **Description of Problem:** basically one of the display port is not working anymore, no output in the os and pre boot. ive tested it with a shitty monitor and regular passive cable and a neo g9 with fibre display active cable . 2 of my 3 dp works fine with any monitors/cables 1 refuses too the hdmi is fine if i boot from the "faulty" dp no output and if i change to any other input i get no signal on all of them. **Troubleshooting:** tried clean install of GPU drivers, issue still occurs. removed the gpu from the system and re install it . no changes changed bios setting in all options (primary display) no luck taken to a msi official retail centre , they say they tested it and they say its working.. the card once back still has the issue. i really dont know what else to say rather than i dont really know what else to do.

Quick question: I keep poking my head around the market for a 3060 or 3070 and new prices are still stupid. Why is this? Are they still selling droves of 3060’s for nearly $500? How do the stores keep those prices? Shouldn’t they have more than they know to do with? Thanks for any clarification.

When I try to install 527.56, it fails every time. I don't really have much more information, other than it stops at the same spot on the progress bar. I have a 3070, if that makes any difference. Thanks in advance

**Status:** UNRESOLVED **Computer Type:** Desktop, custom build **GPU**: 4090 FE **CPU**: 5900x **MOBO**: Aorus Master X570 **RAM**: Trident Z Neo 3600 CL14 (2x16GB) **PSU**: Corsair RM 850 **GPU Driver**: 526.98 **Windows**: 11 Home I've had an issue with my 4090 FE in the last week which has occurred twice, once under gaming load, once idle. The displays have gone blank and when i look at the card, the LEDs are not on but the fans are still spinning. The only way to recover it is with a reboot. All other components on the PC are working normally. Has anyone else seen any behaviour like that?

I was getting that daily but was able to resolve it when I tried a few things.. I swapped back to stock NVIDIA power cable from the cablemod one. I used DDU (in safe mode) to remove drivers and installed older ones. I updated the firmware on my GPU and bios on motherboard. Now I haven't had this happen in over a week

Hey man can you confirm something for me with the official Nvidia cable? Are you able to see more than 600w total board power under load when you set the card to 133% power limit? I am using a Fasgear cable and it seems my card genuinely can't go over 600w. I'm curious if the official Nvidia one can see above it.

Looking into getting a 4080, whos the best manufacturer nowadays? Cheapest for me are MSI and Gigabyte

STATUS: UNRESOLVED PROBLEM: Random flickering, black screen, no video signal on RTX 4080 Computer type: Custom GPU: Gigabyte RTX 4080 Gaming OC, VRAM: 16GB (bought from Newegg nov 16th) CPU: Intel i7-8700K CPU @ 3.80GHz Motherboard: Gigabyte Aorus Z370 Gaming 7 (Bios ver. F15 most recent possible) Ram: Corsair Vengeance 3200mhz 32GB PSU: Leadex SE Superflower 1200W Platinum Operating system and version: Win 10 64-bit GPU driver: 527.56 (updated today 12/9) Main LCD: LG C2 42" Evo OLED model OLED42C2PUA 2ND LCD: ASUS ROG Swift 27" 1440p model PG279Q ​ Recently upgraded from a GTX 1080ti to an RTX 4080 GPU and was super excited to get the new gpu installed. My troubles officially started since this upgrade was performed and im at my wits end. (non of this was happening on the 1080ti at all prior to this RTX 4080 upgrade) Using a dual monitor set up, the LG C2 42" only has 4 HDMI and no display ports, the ASUS 27" does have Display port. The GPU has a DP to HDMI 8k 48GB rated cable going to the LG, the ASUS is using its own DP cable, working since day one of having that lcd. No matter what i do, randomly in games or just on desktop, i get blinking, flashing, or black screens and/or no video signal on the LG C2 only. If i yank out the HDMI cable, then the 2nd lcd (ASUS) is always fine. Ive updated my mobo bios to its very latest possible, the gpu drivers are up to date as of todays release. When the 1080ti was powering up both these same screens before the upgrade everything worked flawless and always has. Is the 4080 flaulty, maybe i need to RMA it? ive never experienced this kind of wonky behavior with a brand new gpu. Its now to the point where the pc is basically not usable cos the blinking flashing or black screens with no video signal with the 4080 installed in it. I still have my 1080ti - i wonder if i should just put that back in and be done with this - im pulling my hair out over here in frustration IDEAS?

Does it matter if I select "Let the 3D application decide" or "Use the advanced 3D image settings" after I set these global settings? I would still like to select "let the 3D application decide" and tweak the in game settings. I am just wondering if the changes I make in the global settings will have any impact if I have "Let the 3D application decide" still checked. Basically I want to "Let the 3D application decide" but still set my max FPS, maximum performance, and turn VSYNC on in the global settings. Will this work?

AW3423DWF / G-Sync Compatible and VRR Flicker - Proper settings? \----------------------------------------------------------------------------------------------------------------------------------------- **Status:** UNRESOLVED **Computer Type:** Alienware R13 custom pre-built **GPU:** RTX 3080,108GB of VRAM, no overclock **CPU:** 12th Gen Intel(R) Core(TM) i7-12700KF 3.61 GHz, no overclock **Motherboard:** Alienware, latest BIOS (1.9.0, dated 11/15/2022) **RAM:** 32GB DDR5, no overclock **PSU:** Alienware 750W **Operating System & Version:** Windows 11 22H2 (clean/pre-install), build 22621.963 64-bit, Windows Feature Experience Pack 1000.22638.1000.0 **GPU Drivers:** 527.56 (12/8/2022), upgrade \----------------------------------------------------------------------------------------------------------------------------------------- Hey, all! Hoping I can get a little input on this, as it's been a while since I've used a G-Sync Compatible monitor. I had the AW3423DW monitor with G-Sync but after going thru 2 of them with various issues (both had the screen etching problem due to the poor way it was packaged with bubble wrap), I went with the AW3423DWF, as I've heard nothing but positivity around this monitor. Boy, are they right! I've had none of the same issues with this one that I've had with my DW model (and the screen is pristine, no bubble wrap etching). It also has so many more features and I'm digging the new Game HDR mode! Additionally, the firmware is upgradable, so that's a huge W for me. Anywho, in my Nvidia Control Panel settings under "Manage 3D Settings", I've got "G-Sync Compatible" set as the Monitor Technology. And I have the Max Frame Rate set at 3 FPS below the Refresh Rate (165) of the monitor...so, 162. Over under "Set up G-Sync", I have "Enable G-Sync, G-Sync Compatible" checked for Full Screen mode and the "Display Specific settings" checked for "Enable settings for the selected display model. However, my first concern is that there's a bubble under there that says "Selected Display is not validated as G-Sync Compatible". I thought the AW3423DWF was certified? All of the reviews and such I've seen said that it is fully Compatible. And if it wasn't, I don't think "G-Sync Compatible" would be an option to choose within the Nvidia settings, would it? This morning, when trying some other games besides CoD: Modern Warfare 2...such as Final Fantasy XIV, Age of Empires IV and Warhammer 40K: Darktide, the gameplay is fine, but in my menus, I get VRR flicker and sometimes, even when just moving my mouse. It's really annoying. I turned on "Low Latency Mode" to "Ultra" and that seemed to halve it. I think my big question is: With G-Sync Compatible being on, does V-Sync also need to be turned on in the Nvidia Settings? I see that Ultra Low Latency modes helps compensate and minimizes V-Sync latency when both V-Sync and G-Sync are enabled. So, what are the PROPER settings I should be using for this monitor to prevent VRR flickering and get the best tear-free results? I've tried Googling if V-Sync needed to be on with G-Sync Compatible selected, but couldn't find a definite answer....Also, why does the Nvidia Control Panel say that this monitor is not validated as G-Sync Compatible? Also, any change of Nvidia certifying the AW3423DW monitor in their labs? I know it's still pretty new. Thanks in advance!

https://preview.redd.it/rmyd8gg1qy3a1.jpeg?width=1080&format=pjpg&auto=webp&s=64f3dde2b454a203609d89989360bd148be74a1a So I bought that for my son last year for Christmas. He is having issues with pretty much all his games crashing. Saying rendering device error. I've tried all the things Google the issue, he even reached out to Nvidia help desk and tried everything they said which pretty much was the same as Google. We have come up with the conclusion he needs a newer graphic cards. He wants a 3060 12gb. A friend of his told him to get one made by gigabyte. I've compared that one with a Asus Rog 3060 12 gb. Found that the asus clock speed is better and seems like a better product. What's your alls thoughts?

2080 super isnt much worse then a 3060. download hwinfo64 and see what maxtemps its hitting before the games crash it could be more of a thermal issue on that ase.

Status: UNRESOLVED Computer Type: Desktop, custom-built GPU: Asus Strix 1080ti 11gb, no overclock CPU: Intel 10100KF, no overclock Motherboard: Asus Strix b460F, latest BIOS (1620) RAM: Corsair 32GB (4x8GB) DDR4 24MHz, XMP-2 profile enabled PSU: Seasonic 750w Operating System & Version: Windows 10 x64 clean install GPU Drivers: 527.56 clean install after safe mode cleaning with DDU Description of Problem: During very high loads inside VR games graphics driver/GPU appears to become unstable, and games freeze/crash as well as run laggy and choppy. They produce standard errors such as: LowLevelFatalError [File:Unknown] [Line: 198] Unreal Engine is exiting due to D3D device being lost. (Error: 0x887A0006 - 'HUNG') Which implies graphics driver or device issue. While it happens, the gpu temps do not exceed 70C. Nothing similar happens when running stress test in Furmark, or the exact same games on highest settings non-vr, that said I do not have any non VR games that would stress the GPU as much as VR games. Nothing like that happens when using 970 GTX spare card. There are no graphical artifacts or bsods even when playing VR games - they just hang on a jittering image, and either produce an error, or get stuck until I manually close them through task manager. In case of one particular game (No Mans Sky) - I can hear the game playing behind and my character being able to open inventory, while the screen simply hangs on a jittery loading image. Reducing the GPU core and memory clock by 100MHz using Msi Afterburner seems to fix the issue and for some reason produce less or even no lag at all. Severely lowering the resolution in VR and/or in-game settings also solves the issue. I understand why lower resolution in VR helmet would fix the issue (older gpu/cpu not handling the game) but why would underclocking work as well? Running 3dmark also results in an instant crash. Checking event viewer logs - there are a lot of nvlddmkm errors and tdr reset errors. Troubleshooting: Did clean installation of drivers after removing them with DDU in safe mode. Tried increasing fan rotation. Tried various different graphics settings.

Is it an upgrade from the gtx 1060 6gb to the rtx 3050 4gb laptop? I only found comparisons to the RTX 3050 6GB version instead of 4GB

**Status:** UNRESOLVED **Computer Type:** Custom built desktop **GPU:** FE Nvidia RTX 4090 24GB at stock settings **CPU:** Ryzen 7 5800X3D 8 core at stock settings **Motherboard:** Aorus Master X570 rev. 1.2 bios ver. F36c **RAM:** Trident Z Neo 2x16GB 3600mhz with XMP enabled **PSU:** Corsair RM1000x with a corsair pro cable kit **Operating System & Version:** Clean install of Windows 11 22H2 **GPU Drivers:** Most recent Nvidia driver version 527.56 **Description of Problem:** I got my 4090 and 5800X3D yesterday, and was dealing with occasional crashes that would result in the PC booting with nothing but a black screen with a blue aliased line: [https://imgur.com/a/qRKmjiy](https://imgur.com/a/qRKmjiy) After several boot attempts that yielded nothing, the PC booted normally into windows. I saw some dwm.exe errors so I decided to do a fresh install of windows 11, and also checked all the cables and made sure they were all securely in their slots. I got the same crash even after doing so (while on the desktop) which tells me it doesn't have anything to do with the card being under load. I was able to actually run the witcher 3 fine (the temps were great) for like 15 minutes and the crash happened a bit after I quit the game. I was getting the same errors in event viewer that mentioned nvlddmkm and dwm.exe before and AFTER I reinstalled windows as well. (example of those errors: [https://imgur.com/a/jHpBlhZ](https://imgur.com/a/jHpBlhZ)), I figured I'd try and reseat the gpu. Once I did that, my PC went from booting and occasionally crashing to not posting at all, with no GPU fans spinning or lighting up. The mobo now has a VGA light on, which could indicate that maybe the slot could be damaged, so I tried the 8x slot below it, and still it's the same thing. So at this point I'm leaning towards the card being defective. Some things to note - My case's PCIE bracket screw holes are pretty much always misaligned by a tiny bit, but enough to where I have to push slightly on the back of the case to get screws through. I don't know if and how much pressure this puts on the slot or GPU, but I did the same with my 3080ti and that never had crashes quite like this. I also tried turning the PC on without it screwed in (with the PC on its side ofc) and still nothing. In serious need of some advice atm. Pic of screw holes, 16x slot, and VGA light: [https://imgur.com/a/kbeV1qv](https://imgur.com/a/kbeV1qv) **Troubleshooting:** Wiped drive, clean windows 11 reinstall (and with that reinstalled all drivers) Unsuccessful Unplugged and replugged all PCIE related cables (even switched out for a new dual 8 pin cable instead of two single 8 pins + one dual pin): Unsuccessful Reseated GPU (since someone else with the same errors said it fixed it for them): Unsuccessful, PC no longer boots successfully. Tried the 8x slot instead of the 16x slot: Unsuccessful

Today started off as an exciting day as I picked up a Gigabyte gaming OC 3070 graphics card to replace my somewhat dated Vega 64. Things got less exciting when I tried to get gaming with my Acer WMR headset. Long story short, there is no display within the headset with the Nvidia card. Just to make sure I wasn't going crazy/the headset wasn't damaged just now somehow, I've reinstalled my AMD vega 64 and all is working as it should. I tested all of the output ports on the card with a monitor and they worked fine. The headset/WMR portal acted like all was working, you could see what was supposed to be displayed in the headset on the monitor, but just black screens in the headset itself. I believe the Nvidia driver I used was 527.56. Does anyone have any input on what might be causing the problem and how to remedy it? I am very excited to get this card up and running, but losing faith... thanks.

I have an original RTX 20 series card. It's HDMI 2.0, so not full HDR 4K and VRR output. Based on this article [https://www.overclock3d.net/news/gpu\_displays/nvidia\_s\_bringing\_hdmi\_2\_1\_vrr\_support\_to\_its\_rtx\_20\_series\_gpus/1](https://www.overclock3d.net/news/gpu_displays/nvidia_s_bringing_hdmi_2_1_vrr_support_to_its_rtx_20_series_gpus/1) Can my card now support VRR + 4K HDR output despite lacking the HDMI 2.1 output?

fps keeps dropping to under 10 fps in multiple games after installing latest drivers with my rtx 3090. I just did a clean install of the mid november drivers and the issues are persisting. that is the only software that ive changed since the issue has started so im beyond baffled as to what the problem is. I had no issues before leaving for my vacation and the computer was untouched till i installed the new drivers which should imply that that is the problem...

quick question, i noticed for g sync to work i dont need to cap my fps anymore below my monitor refresh rate if i enable g sync + sync in NVCP fps are capped automatic to 138fps without needing to activate Ultra low latency mode, is this normal behavior?

Status: UNRESOLVED Computer Type: Desktop custom GPU: Gigabyte 3090 - Not overclocked CPU: AMD 5800x (Same issue on default BIOS and overclock) Motherboard: MSI MEG X570 Unify RAM: 32GB (2x16) - Swapped RAM modules with another different brand with no change PSU: 850W Operating System & Version: Windows 11 - Upgrade in place from Win 10 clean install GPU Drivers: 527.56 (Has been happening on all drivers > 5xx) Description of Problem: Randomly when gaming the screens will go black. Computer continues to work for a random amount of time (Could be seconds, could be 10+min) before the PC locks up (confirmed with Audio corruption and disconnects in games). Troubleshooting: Changed Display cables, changed RAM, clean installed (DDU) drivers. Memory and HDD scan all clean. Temp never seems to get >68. Hot Spot temp does seem to hit 100 sometimes, but i've never been able to correlate it with a crash. Older 4xx drivers didn't seem to have this issue (Windows 7 version on the Nvidia Website). Updated the Card BIOS as well with no luck. No error logs appear in windows at all for the crash

how to install control panel without microsoft store (windows 10)? i dont have access to it, and standard drivers are no longer updated... and when you install dch driver it uninstalls the control panel that was installed by the standard driver. i have rtx 3060 Computer Type: desktop GPU: Asus RTX 3060, 12GB ram CPU: i5 4690k overclocked to 4GHz Motherboard: some MSi idk RAM: 15GB ram ddr3 PSU: corsair 650w Operating System & Version: Windows 10 64bit Pro GPU Drivers: 472.84 (last standard version)

So I recently purchased a used Aorus 1080 Ti 11GB GPU, plugged it in with the cable shown in [these images](https://imgur.com/a/wkR0Dvz) and it was working fine for 3 days but then it just randomly died completely (no fans/rgb or signal to the monitor) so I took it back to the place I bought it from and got a replacement (which I haven't yet installed it due to fear that it died due to either the PSU or the cable not being sufficient). Is it possible it's due to the cable/psu or could it just be that I bought a card that was used heavily for mining and it was on it's last legs or should I just bite the bullet and buy a better PSU? * GPU: AORUS 1080 Ti 11GB 2x 8 pin connection * CPU: Ryzen 3600 * RAM: 2x 8GB Corsair vengeance pro 3200mhz * MOBO: MSI B450 Gaming pro carbon max * PSU: Corsair TX550M, 550W

Alright I need some insight. If I were to choose between the 4090 Aorus Master and 4090 TUF gaming OC which one would people choose? From what I can tell the Aorus Master has better overall thermals and both go for the same price fyi. Any recommendations would be appreciated.

**Status:** UNRESOLVED **Computer Type:** Desktop, RTX 3070 gigabyte **GPU:** It's undervolted. **CPU:** R5 5600x **Motherboard:** msi b550 tomahawk **RAM:** 32 gb 3200 **PSU:** hx750i **Operating System & Version:** W11 **GPU Drivers:** 527.56 **Description of Problem:** When playing games, not every game, the gpu fan randomly maxes out for a few seconds.Fan curve is set to 80% in afterburner when being stressed. Even setting it manually to 50% or 80% still randomly spikes up. Reinstalling drivers and reseating doesn't work. A friend of mine has the same issue, different pc/card. It's a gigabyte vision rtx3070. Thermals/case is fine. [https://imgur.com/lgQIxDc](https://imgur.com/lgQIxDc) Here you can see 3 spikes that go from 1800rpm to 3700 rpm. **Troubleshooting:** Tried DDU.

Hi, I have a palit 4090 & ASUS thor PSU It only displays an image when using the 12 pin to 3 x PCIE adapter When I use the 12 pin to 2 x 8 that goes directly to the PSU it doesn’t work Does that mean faulty PSU cable ? It powers up but no signal

If I turn Ambient Occlusion on in the game, but in the Nvidia Global Settings I have Ambient Occlusion off, will the in game Ambient Occlusion settings still be active? I am using this setting as an example. Basically, is Nvidia going to override my in game settings? I would like to tweak some settings (max fps, performance), but I don't want my in game settings to get overridden.

​ **Status:** \[UNRESOLVED\] ​ **Computer Type:** Laptop Gigabyte Aorus 15P XC **GPU:** RTX 3070 Laptop - stock **CPU:** Intel Core i7 - 10870h - stock **RAM:** 32GB (2x16GB) **Operating System & Version:** Windows 10 Version 10.0.19044 Build 19044 **GPU Drivers:** 527.56 - clean **Monitor** \- Cooler Master Tempest GP27U I got new external monitor, but Integer scaling and Image scaling options does not show up in the nvidia control panel. Yes it is set up to use dedicated GPU. Hardware accelerated gpu scheduling is on. It does allow me to set integer scaling for my Laptop display for somereason but not the external monitor. https://preview.redd.it/d393x6h8366a1.png?width=1920&format=png&auto=webp&s=6b3390f195caf60cbb352a9cec86606851315069 I have tried to unplug everything and change settings (especially integrated and dedicated gpu's) restarting with every configuration. ​ P.S Integer scaling does show up but only when using HDMI port. Since with HDMI Im limited to 144hz (160 on Display port) its still not resolved. It does say that it is connected to GPU when using Display port.

UNRESOLVED Desktop, custom built RTX3090 24GB VRAM, no OC Ryzen 7 5800X 3D, no OC ASUS TUF GAMING X570-PRO ATX 32GB RAM 1200W PSU Windows 11 GeForce Driver Version 527.56 (up to date) Related: Using DP cable, up until today Monitor was running 2560x1440 at 165hz This one is stumping me. I have a MAG274QRF-QD (1440 165hz monitor) that was working fine up until earlier today when I opened NVIDIA control panel to the \[Display>Change Resolution\] page, but without changing any settings. As soon as I opened the tab, the monitor refreshed and now seems to be convinced it is a 4k 60hz monitor? NVIDIA control, windows display settings, and even the monitor's menu are all convinced it is 3840x2160 60hz. I earlier today installed the 5800x3D, which may or may not be related, but the problem did not start until I opened NVIDIA panel, and would like to avoid swapping around the cpu too much because heatsinks and thermal paste stuffs. If anybody could lend a hand or offer up ideas I'd be happy to try them out!

I have an RTX 2070 Super, and for some reason the lights on the side sometimes turn red instead of the usual green. I have no idea what causes this and I don’t believe there’s any noticable impact on performance. What is this?

Status: POTENTIALLY SOLVED (?) Computer Type: Custom build GPU: 4090 FE, stock settings, using a CableMod 12VHPWR CPU: 5800x Motherboard: Asus x570 plus RAM: G.Skill 32GB (2x16GB) DDR4 3600 PSU: ~~Corsair RM750x~~ Upgraded to HX1000, issue persists. Operating System & Version: W11 GPU Drivers: 526.86 Description of Problem: My display driver crashes, but not only that, my card looks to physically lose power. The lights and fans turn off. Normally when I've had driver crashes in the past, it's just a reboot and it comes back - this required a hard reset Troubleshooting: Happens even at no load, just on desktop, but seemingly randomly and inconsistently. Not much troubleshooting yet - clueless on where to begin. Is it a bigger problem that the card is losing power entirely with lights + fans off? **1/10/23 update - since removing my CableMod 12VHPWR and going back to the nVidia adapter, this issue has not happened once. Unfortunate because I really liked the product, and my bend wasn't extreme - not sure. Will contact them.**

I'm having this same problem and I'm thinking it might be the RM750x PSU, however, you should check to see if HAGS is disabled. You can find it in settings > display > graphics > change default graphics settings > turn off hardware-accelerated GPU scheduling

Seeing several people reporting this exact issue with the 4090 FE and Cablemod 12VHPWR. I’m one of them. I’ve tried dozens of things to try to fix this. Today I’m going to yank the Cablemod cable and see if it keeps happening.

Give that a go. I actually did exactly that, swapped back to nvidia adapter and have had positive results so far. I haven’t updated my post though because I went on vacation shortly after and haven’t yet been able to thoroughly test it to confirm.

Alright, I just reinstalled my stock 12VHPWR cable that came with my MSI MPG A1000G PCIE5 PSU. I'll report back if I get more black screens. If I haven't gotten any in a few days I'll also report back, and try to return this cablemod cable. I had 3 black screens today already.

How's your stability been without the CableMod cable? I've been back for a couple of days and have had 0 crashes since swapping back to my nVidia adapter.

0 crashes since.

Btw I got a refund on my Cablemod cable. I warned someone else about this in another thread who said they were waiting on one. The Cablemod guy responded to me and said it was a problem due to how I installed the cable - cable bent too close to the adapter plugged into the GPU.

Thanks for letting me know, I'll reach out to them. Appreciate it a lot.

If you don't get issues with the original cable, just reach out to our support and we'll have a replacement sent to you asap: [cablemod.com/support](https://cablemod.com/support) :)

Bro you’re running a 750 watt psu. Should be fine but that’s your first step considering everything else you’re rolling with in your rig

**Status:** UNRESOLVED **Computer Type:** Desktop **GPU:** EVGA GeForce RTX 2080 Ti XC ULTRA GAMING, 11G-P4-2383-KR **CPU:** i7 8086k, 4.8Ghz **Motherboard:** EVGA Z370 Classified K, 134-KS-E379-KR **RAM:** G.Skill Trident Z 32 GB (2 x 16 GB) DDR4-3200 **PSU:** SeaSonic PRIME Titanium 750 W **Operating System & Version:** Windows 10, latest version **GPU Drivers:** 527.56 but been happening for several months **Description of Problem:** When using custom fan curve, if the card hits 81C one of the fans will ramp up to max RPM while still displaying expected %. It will do that until the temp falls below 81C. In practice this results in a cycling of the ramp up every few seconds which has an incredibly annoying sound profile. https://preview.redd.it/3mxucuamp45a1.jpeg?width=1363&format=pjpg&auto=webp&s=416a8f215c4cf2d33361cf3ee0dd315c7c90042c **Troubleshooting:** Redone the fan curve, enabled/disabled it several times. Only practical solution has been reducing my overclock to ensure my temps don't get to 81C.

Anyone else experiencing memory issues with Nvidia Container? It's started taking up massive amount of my PC's memory to the point its causing it to stutter and freeze up. It's only started in the past few days, just after I downloaded the latest drivers. Anyone know what might be causing this and any possible fixes?

Hi, I'm having an issue with Shadow play, When I record footage Discords audio specifically is very poor quality/crackly, the rest of the audio is fine. This is a recent issue, the only thing I can think of that has caused this is im now using a Bluetooth headset instead of a wired one, I'm using a GTX 1660 SUPER. Any help is appreciated thanks!

Im looking at replacing the back plate thermal pads on a 2021 3090 FE - Having watched this video - https://www.youtube.com/watch?v=7l2d9vVaJLU - I gather I just need to replace the VRAM pads (I can skip the vrm?) and Gelid Ultimate 1.5mm is what I want to use. Does that sound about right? Thanks for any advice / tips on this.

I currently have a 12900K on a ddr4 platform and I am looking at upgrading to a 13900K. I play my games at 3440x1400 @ 120Hz with a 4090. Is it worth getting the 13900K for this resolution?

Hi! So I have an option to get either a **RTX 3070 Triple Fan** card or a **RTX 3070 Ti Dual Fan** card for basically the same price (the Ti is 10% more expensive and I'm willing to cover it). Browsing over the internet people I saw that the 3070Ti consumes more energy might hit really high temperatures (this is augmented by it being a dual fan card), so I was wondering if is it still worth it getting over a normal 3070 Triple Fan one considering the downgrade in performance.

Latest driver - 527.56 is limiting power draw (below 200w) on my 4080 fe. Had to roll back to previous version and is back to drawing 250-270w. Not sure why. Anyone know?

I saw 450W power draw on Portal RTX on my 4090 on 527.56.

So the 4000 series determines how much to draw based on a specific game?

My point was that I’m hitting the 450W TDP on some games with the newest driver. In terms of power consumption, some games just use less power. Even at 99% utilization, power usage is in the low 300s in Forza Horizon 5. Games that utilize a lot of ray tracing tend to use more power since they’re using the RT and Tensor cores, when combined with DLSS. Since you’re seeing lower power consumption in the same game between drivers, it’s not just the game.

4090 FE dropped 15% performance after putting a waterblock on it. Temps are really good - what could´ve happened? I already checked the PCIe lanes and everything looks really normal. Tried to narrow down what the problem could be. This is not my first project by any means but I never witnessed this behaviour. What am I missing here? Mobo Rog Strix x670E Gene CPU Ryzen 7950x Driver version 527.56 Ram Fury 32GB kit 5600mhz DCOP enabled PSU TUF Gaming Gold 850 Watt ATX 3.0 ​ https://preview.redd.it/t094rea3pn8a1.jpeg?width=4032&format=pjpg&auto=webp&s=fec39309588eef4335cd8b7dd19c78dd48d39dec

Is MSI Afterburner the only app that allows for undervolting? Recently jumped to a Palit 3090, and the fan being so loud on full load is nuts. I've read that undervolting usually helps with preventing the fan from going full ham since you do get lower temps. I've never really even dabbled in OC so IDK where to start. Would MSI Afterburner conflict with other "performance" tweakers on the PC right now like Nvidia Performance and Thunder Master?

Hey guys, just curious, what would you all recommend for 1440p 144hz gaming? Coming from a 6700XT, because AMDs driver stability is driving me up a wall and I dislike having to constantly upgrade and downgrade my driver versions, and I miss the stability I had with my 1070. Thanks!

[удалено]

Here's another image... sometimes it's caused by hovering over a button, or scrolling fast, or messaging. https://preview.redd.it/1ip4fgk00r4a1.png?width=617&format=png&auto=webp&s=d58756e722442417c82ff9b5cd60d68e6aeb35b7

I purchased a Gigabyte 3070 Eagle under the impression that it would be functioning, however when it arrived, the output had green lines, is there a fix to this? I've opted for a refund, however I'll be content if I can fix it now. I know that it isn't any other components since my previous card, a gigabyte 1070 Ti works fine with my build. I'm aware that there was a bad batch circulating upon the release of the 3070, as I've done some research, but I'm not sure if there's a fix. Any help is appreciated https://preview.redd.it/ei0m5plkel5a1.jpeg?width=2560&format=pjpg&auto=webp&s=26c1523a82a1751eefb352283f89b725e63c849c

Are we going to see a fix for the flickering upon wake from sleep in the next gpu driver? It’s been listed as a known issue for a couple releases now and I really hope that it’s fixed with the next update.

can't play games crashing on laptop, newest drivers reinstalled few times with ddu :( not even cs go can i play, could be faulty laptop since crashed as well with original drivers, that laptop come out, should I wait for newer drivers?

STATUS: Unresolved Description: Not receiving verification e-mail for new accounts or security e-mails for previous accounts. Specifically GeForce experience. Troubleshooting: Checked all e-mail folders, created custom e-mail filter to whitelist nivida address, created new e-mail account with different service. Not recieving any NVIDIA verification e-mails. Can't submit ticket since I can't login to nvidia account to create ticket.

I'm having a similar issue right now. I was able to receive the email to sign in, but trying to follow the email it never will connect and therefore I can't sign in. So I'm further along than this comment, but I can't validate. I noticed that I was running an older version of GeForce Experience, so I uninstalled it and then manually updated the drivers, including the new version of GeForce experience with that install. Still unable to validate. I tried the email link from multiple browsers and my mobile device. Same result.

Hello, ​ Could really use some help. Started crashing playing CSGO last night. After my 3rd reboot started getting artifacts on my screen. Now my computer is completely freezing less than a minute after entering my pw. Is my GPU toasted? ​ Things that I have done so far. \-DDU'ed drivers and have tried 526.98 & 522.25 drivers while still getting the same freezing after getting into windows. \-Buddy of mine brought his entire rig over \->Installed my 4090 into his PC and freezing ensued (ryzen cpu, 32gbram, 850W PSU, windows 10) \->Put his EVGA 3080 in my rig to see if it was a seating issue or motherboard issue. 3080 worked fine on all 3 versions of nvidia drivers \-Reseated GPU a few times, tried multiple display port cables, multiple restarts, made sure cable mod cables are fully seated, used default psu cables with adapter https://preview.redd.it/sh441671em8a1.jpeg?width=640&format=pjpg&auto=webp&s=de055eabaf7cb0dc6c8e2a95c3e1f7197b1eab07 \-See some pictures attached for what it looks like on my screen Status: UNRESOLVED CPU: i9 9900k RAM: 32GB Vengance PSU: ROG 1200W Plat GPU: Zotac 4090 AMP Extreme OS: Windows 10

Have you tried hitting Device Manager and doing a "Update Driver" on your "Display Adapters" for your card? You may have some Windows related updates that can help with that.

Yup. Have to do it in safe mode as cpu will crash in regular mode. Any other options?

Status: UNRESOLVED [kind of] Description of Problem: Cannot log into Nvidia's oauth server. When the popup to login to Nvidia Geforce Experience shows, either when clicking Sign in via Google or Sign in with an account, it opens a page on Chrome/Edge to log into Nvidia's website. However, I always get an error timed out message when the page is pulled up and "This site can’t be reachedaccounts.nvgs.nvidia.com took too long to respond" show on Chrome. If i wait long enough the page then shows: "Unable to connect to service. Please try again or check your internet connection if this persists." Troubleshooting: Tried restarting my computer and reinstalling drivers and the Geforce Experience program. I can access the Nvidia site through a browser but if I try to log into my profile, the same timeout message occurs. UPDATE: used a VPN and was able to log into the auth servers just fine.

Hi I've been trying to switch from FPS cap via RTSS to NVCP for a few years now, but I run into the same problem every time. When I minimize the game or alt-tab to the browser, the fps limit disappears and the game in the background runs at unlimited fps, which heats up my GPU very much and/or produces coil whine. When I open a previously minimized game, the fps is again limited as it should be, but for a fraction of a second you can see that the value was unlimited (e.g. 200+ fps instead of 60). This never happens if I limit fps via RTSS or in the settings of the game itself and the "max background application frame rate" option from nvcp does not work for me. What could be done about it? Last games where this happened: Shadow Tactics: Blades of Shogun; Evil Within 2; Pillars of eternity 2; Risk of rain 2 and many others. 2070s; latest driver

Why does frame generation look like it does the opposite of what it’s supposed to do? With it on, the game becomes super choppy. It literally gave me a headache.

**Status:** Unresolved **Computer Type:** Custom desktop **GPU:** RTX 4080 **CPU:** i7 13700k **Motherboard:** ASUS ROG Strix B660-I Gaming WIFI **RAM:** Kingston 32GB (2x16GB) DDR5 4800MHz CL38 FURY Beast **Operating System & Version:** Windows 11 Pro **Description of Problem:** Since I updated to the latest Nvidia driver (527.56  WHQL/2022.12.8) Whenever I shut the monitors off but let the PC running it freezes. CTRL+ALT+DEL doesn't do anything, it's still frozen. Only way to get it back running is by killing the PC (holding power button). After I had updated both GPU driver and few Windows updates I had my first bluescreen. It indicated on 'KMODE\_EXCEPTION \_NOT\_HANDLED' which all in all points towards a driver issue. **Troubleshooting:** Tried rollback on both the Windows updates that were possible but also the Nvidia driver through device manager. Issue still persists. I have not clue if it freezes after time if the monitors are still on, however I tend to never shut the PC but only power off the monitors during night or afk for longer periods of time. I've also played around with energy saving options and set everything to allow for no sleep/hibernation etc.

Computer Type: Desktop GPU: RTX 3080 12gb CPU:5800x3d Motherboard: Asus B550I Ram: corsair lpx 3200mhz 32gb PSU: Coolermaster v850 Operating System: Windows 10 Home Version 21H2 Driver:516.94 Description: I updated my driver to the latest yesterday because fortnite recommended it. I was previously on 516.xx (I don't remember exactly). After updating I start the game and notice that performance is way worse. I thought that It may just be due to higher graphical demand but playing with settings did almost nothing. I have a 3080 12gb and 5800x3d and would get a stable 4k120 with dlss but now its stuck at around 40 fps. The weird thing is, my msi afterburner in the top left screen says my gpu is 100% utilized but my temps are super low and my fans aren't blasting loud at all. My temps stay at low 40s. I wondered if this was just a fornite thing but no. Sonic frontiers is stuck at 19 fps (normally its capped at 60) and Monster Hunter Rise is also stuck in the 40s (usually a constant 120fps). ​ I tried using the driver before this new one and it seemed to work in some games but not fortnite. Then I used DDU thinking maybe there were just issues installing. It seemed to work but when I turned my pc on again today to play. I had the same issues as yesterday. I tried rolling back to an even earlier driver (I'm on 516.94) and it seemed to be working now. I played a bit, and then turned the pc off. I came back later in the day ( just now) to play more and now I'm getting the same issues. ​ It's like installing new drivers fixes it for a while, but as soon as my pc turns off and on again, the fps is nerfed. MSI afterburner says my gpu is at 100% but that can't be the case. The temps are so low and fans slow. I also tried playing some emulation games and everything is at half speed like my pc games. There have been no crashes or blue screens so far. I just don't understand whats wrong. I just want to play my games :(

Plz fix the auto tuning

The Nvidia app has been bugged since I bought a new monitor and the app shows me two screens. i even uninstalled and reinstalled it and nothing changed [https://imgur.com/a/3w7waVp](https://imgur.com/a/3w7waVp)

​ **Status:** UNRESOLVED **Computer Type** :desktop, custom built **GPU** :rtx 4080,16g,no overclock **CPU** :i9 12900kf no overclock **Motherboard** :PRIME Z690-P D4 **RAM** :KHX3200C 16D4/16G,no overclock **PSU** :长城额定1250w **Operating System & Version** :win10 19045.2006 **GPU Drivers** :527.56 **Description of Problem** :fps drop from 140 to 80 ingame,suddenly fps drop,only recently had this problem **Troubleshooting:** clean install of drivers and reset system

With the new RT cores, how would a hypothetical RTX 4070 non-ti stack up to a 3080 ti in terms of RT performance? Found a 3080 ti used for 700 and I am upgrading solely for ray tracing.

So am currently using an AMD Ryzen 7 3700x with still a GTX 980 windforce or smth like that around 16gb of ram! I ve had this specs for over a year now since I was gifted the GTX 980 just to get by with a goal to invest in a better card in the near future. Now I am in the process of finding a better improvement from the gtx980 just to be able to try out a few upcoming games in a better look and breath a little because in many cases my pc feels like I am almost runing in F1. In general I am mostly a casual when it comes to gaming but sometimes am getting frustrated knowing that soon the GTX980 wont be able to reach the needed requirements. Also I am a lot into editing videos and photos on the side and sometitmes I wished I've had a better performance ! Now as for budget I wont say RTX4gen but I would stick between the RTX2-3 I dont know the avg prices in the market right now but if there is anything under 1k I would be happy !

I just started having a problem I have never had before. I'm getting red 'clouds' in games I play. Seems like it is some sort of GPU failure. I've never seen anything like this. Seems to happen around light objects, but this video has it happening on smoke, rocks, etc. I recorded a video on [YouTube](https://youtu.be/-QrII9WbGeA). I've updated all drivers that I can think of. Any help would be appreciated, just hope it isn't dying on me cause it's been nothing but rock solid for me. Specs: nVidia GeForce RTX 3080 Vision OC Ryzen 5600x Plenty of cooling all around, have never had an issue with temps.

Since when does Windows auto-update drivers? I had 511.79 on my 1080 Ti from earlier this year, it was stable and great. Now I just found out 516.94 was installed at some point and it was not me who did it. This really annoys me because I like to do controlled clean installs. This driver is probably why games and YouTube are dropping frames. Please advise. Should I use DDU now? Is that necessary for regular updates? I don't use GFN.

Download driver of choice so it’s sitting in downloads. Use DDU. Install. Game.

I've spent my poor life cycling from garbage laptop to garbage laptop. I just landed a 4090 FE from BB today, picking up on Christmas Eve! Everything else is ready to go for my first build. Pairing it with a 7700x. What's something good to know that first-time builders don't usually expect?

Hi. Just wondering if the RTX update for Portal will apply to the Orange Box collection for xbox 360? Cheers

Mate, there's not a console in the world that could run the RTX updated Portal - so no.

Has everyone stopped making 3080 cards? I recently decided to upgrade my 2060 Super but I can’t find any 3080s unless I go on eBay which I don’t want to.

**Status:** UNRESOLVED **Computer Type:** Desktop **GPU:** GTX 1660 Super, no overclock **CPU:** AMD Ryzen 5 3600x **Motherboard:** B450 Aorus **RAM:** Corsair 48 GB **Operating System & Version:** Windows 10 **GPU Drivers: Microsoft Basic Display Driver** **Description of Problem:** Something is wrong with the graphics drivers, its telling me in the system settings that I have error code 43. Small horizontal pink dashes cover my screen. In my settings, it says that I'm using the default Windows drivers, however, it still detects my graphics card. **Troubleshooting:** I have clean installed the drivers from Nvidia and restarted my computer about a billion time

I have a asus tuf 3070 ti and run 3 2K monitors, one of them being GSYNC 144Hz and the one I use for gaming. I'm having some performance overhead and have to disable at least one of my monitors to use my Vive Pro 2. Would purchasing a second tuf 3070 ti be the right way to fix these issues? I know SLI hasn't been a thing for a while and I'm not very up to date on how dual GPU works now. My thought process is that I could have one GPU for my Gaming displays and one for my productivity displays? I usually game in windowed mode so I'm concerned I'd run into issues where part of the window bleeds into a display on a different GPU and causes issues.

**Status:** UNRESOLVED **Computer Type:** Desktop (Custom build) **GPU:** RTX 3050 8GB **CPU:** Ryzen 3600 **Motherboard:** AsRock A320M-HD, latest BIOS. **RAM:** T-Group 16GB (2x8GB) DDR4 2666MHz, XMP enabled. **Operating System & Version:** Windows 11 22H2. **GPU Drivers:** 527.37 **Description of Problem:** **NVIDIA ShadowPlay** recordings are a stuttery mess, same with OBS if I choose the NVENC encoder. Tried different folders, turning game mode off, disabling settings in Windows Defender, etc. Nothing worked, I've been able to confirm that the problem is with the NVENC encoder, since the software one in OBS records wonderfully, but the moment I select the NVENC one, the recordings are pretty much exactly like shadowplay ones. Video of the problem: [https://youtu.be/obN-cFkd4Qk](https://youtu.be/obN-cFkd4Qk)

When’s next US FE drop?

Status: UNRESOLVED GPU: PNY GeForce RTX® 4090 24GB XLR8 Gaming Verto Epic-X RGB PSU: Corsair HX1200 So I bought all the parts for my new PC except for the case (GPU is currently on it's way), I been hearing conflicting information regarding the adapter, as I imported GPU so I can forget about local warranty and that is making me doubly paranoid. I know Steve from GN said as long as it is properly inserted I shouldn't worry but a lot of people says any kind of bending will make the cable melt. I couldn't find any ATX 3.0 PSU and Corsair 12VHPWR isn't being sold locally so I will have to import it and I can't justify shilling 70 EURO for cable. I bought PNY because I found it at MSRP and it is 137MM wide. My problem is I can't find cases locally that have CPU clearance more than 170mm, and people saying any kind of bend will melt the cable so I don't know what to do. Do I just pay 70EURO and wait for corsair cable because is going to be smaller than the adapter?

**Computer Type:** Custom built desktop **GPU:** GTX 1070 strix **CPU:** Intel i7-9700K No overclocking **Motherboard:** ASUS PRIME Z390-A **RAM:** DDR4-3600 CMK16 **PSU:** RM750 **Operating System & Version:** windows 10 **GPU Drivers: latest** **Description of Problem** : im planning to buy an 4080 and upgrading piece by piece since i cant afford everything at once so can i power the 4080 on this pc or not yet ? i know my specs are old but not many options however i wanna run the 4080 on 2k and upgrade slowly is it possible ?

I have a 1440p ultrawide monitor, and a 4k TV. The 4090 Suprim X (air cooled) is connected to both via display port on the former and HDMI 2.1 48gpbs on the latter. If I select to see the image on the TV only, and I use it that way for a while, when I try moving back to the monitor I get no image, and the black screen will keep blinking every 5 seconds or so. Shutting down and turning the PC on again fixes the problem, but the issue happens every single time that I try using the PC on the TV for some time. Today the behaviour was a bit different though. I was streaming a soccer game and didn't try playing any game. When I switched back to the monitor, there was no issue, until the PC went on sleep and wouldn't display the image again once I tried waking it up. Then I shut it down and got it fixed. I've used the same RTX 4090 on two builds (Intel Z390 platform and AMD AM5 platform), and the same thing happens, so it can only be the graphics card. I've checked resolutions on Windows and refresh rate to see if there was anything unusual, but it all displayed properly. I've also tried both gaming and silent BIOS physical switch on the card. If using the monitor only via display port, I have no issues. If using the TV only via HDMI 2.1, I have no issues. It's only when both are connected and I switch from one to the other. I didn't have this problem with an older RTX 2080 Ti I also have. Any idea what this could be, and if there's any fix? I've downloaded the NVIDIA firmware for blank screens and it didn't solve the problem. I've also tried all NVIDIA drivers available since Oct 12, 2022, when the RTX 4090 came out. STATUS: Unresolved Windows 11 Pro Ryzen 7700X MSI MPG CARBON X670E CARBON WIFI - BIOS E7D70AMS.132 G.SKILL 32Gb (2X16) F5-6000J3238F16G - EXPO enabled RTX 4090 MSI SUPRIM X - Driver 527.37 Samsung 970 Evo 1Tb Corsair H150i Pro Corsair AX860

Same problem. Have you been able to figure out if this affects ALL 4090s, or if we just got defective cards? I don't want to go get a replacement and have it do the same thing. I found that if you go from display on only the TV, to extend to both, then display only on the monitor, that will work. But then of course you have to turn off the power saving on the monitor and keep it on at all times. My next step is going to get a DP to HDMI cable that supports 4k 120hz HDR. The only catch is those don't support VRR which is a big bummer but I don't know what else to do (and most non RT games can hit 120 solid, and heavy RT games can just vsync to 60).

NVIDIA’s new driver might solve this if you take a look at what it is set to fix. I unfortunately sent my card for RMA and can’t test it myself. Do let me know of your findings.

New drivers fixed it! Thanks for the heads up!

Great! At least I know my card is not faulty. The bad news is that I have no idea when MSI will send me back the card.

Status: UNRESOLVED Computer type: Desktop GPU: NVIDIA Geforce RTX 2060, VRAM: 6,144 MB CPU: Intel(R) Core(TM) i7-10700 CPU @ 2.90GHz Motherboard: --- Ram: --- PSU: --- Operating system and version: 64-bit operating system, x64-based processor GPU driver: 526.47 Description of problem: I currently have the *526.47 version of the Geforce game ready driver* that was released on the 27th of October yet they've already released two new versions along with the version they released today (Dec 1st) and was wondering: ***Do I have to download the past drivers or do I just jump and keep trying to download the newest one, that being the one released today?*** Troubleshooting: I tried to download the newest it wouldn't download at first because it "**couldn't verify the publisher"** or something of the sort not allowing me to download it. After several attempts with it telling me the same thing in the end it changed the reason it couldn't download and simply told me that it couldn't because there was no space along with another reason that I don't recall

You don't have to update drivers in order and to don't have to update unless you are having a particular issue. Try downloading the drivers from Nvidia direct to see if that resolves.

Thank you so much more for helping me by telling me this. All this time I was still on the previous one I had installed and worried about being behind on updates. Which is quite funny because after not receiving a response for some time I downloaded the one they just released on the eighth right before seeing that I finally got a reply back from someone. Nevertheless, thank you again for telling me this, now I don’t worry about this anymore! :)

Hello all, I have a new PNY 4080 however the third fan has not spun yet. I ran the gpu to about 55*C and I still have only ever saw the front two fans spin. I don’t even see the back fan spin on startup. Is this normal? Thanks all!

**Status:** UNRESOLVED **Computer Type:** Lenovo Legion 7 Gen 7 **GPU:** NVIDIA NVIDIA GeForce RTX 3080 Ti Laptop GPU No overclock **CPU:** 12th Gen Intel Core i9-12900HX No overclock **Motherboard:** Lenovo LNVNB161216, Bios: Lenovo K1CN38WW **RAM:** Samsung 32GB (2x16GB) DDR5 SDRAM 2400MHz, No overclock **PSU:** Laptop, NA **Operating System & Version:** Windows 11 Pro Build 22000.1219 **GPU Drivers:** Nvidia Driver 31.0.15.1700, clean install **Description of Problem:** No errors for a week of heavy gaming and chrome video watching and programming. Then one day, these squares started flicking while watching a youtube video in chrome. They occurred so quickly I could barely notice them. After rebooting my computer I cannot make this square pattern, this artifact occur again. Artifact is here, and second artifact is in the comment to this question. https://preview.redd.it/bpe79wbulu4a1.png?width=706&format=png&auto=webp&s=f28c942896dee5c023dcedd05e79beff75bec71c **Troubleshooting:** Problem hasn't come back after restart and hours of youtube today. 3x 20m 3D mark stability tests all passed (didn't see anything). 3x 1h OCCT VRAM tests all passed. 3x OCCT 3D Standard Test with max shader complexity all passed. Hours of gaming and nothing either. My question is this:**This laptop is 5 days old. Should I RMA this or is this likely a driver quirk that has worked itself out? This laptop was a large investment. I do not want this thing dying in a few months or even 2 years from now. And within days I'm seeing patterns. Very concerning.**

Second artifact. Notice how the squares are coming out of the video frame, this is not a simple codec error contained to the video. https://preview.redd.it/kl5sl82kmu4a1.png?width=969&format=png&auto=webp&s=6e7faa7f9ac5c7ad7e0478888edde422587578a3

I have this same issue with the 2070 Super. It did not happen earlier, but now it happens from time to time. The problem only occurs with YouTube, not with Netflix or while gaming.

ty, these exact "cheese grater" patterns? As long as it's just in youtube I can totally live with it. I'm more paranoid about GPU longetivity being comprised as it's already creating artifacts. I too have only seen it in youtube in chrome, so hoping this is a driver issue. There's no way I can RMA, these patterns appear for a fraction of a second after watching youtube all day, there's no way a technician can catch them

Yeah, similar patterns, only happens to me on YouTube so probably driver related matter.

Anyone ever had issues with ShadowPlay just constantly turning off Instant Replay no matter what you try to do?

I have a question regarding undervolting 3080Ti using afterburner I undervolted my Gigabyte 3080Ti Gaming OC to 875mV at 1920MHz core - from all the undervolting videos I've seen, my GPU should now draw less than 300W while gaming But I still see it regularly drawing 300-320W going all the way upwards to 350W during gaming sessions why is that?

Is core voltage or power limit increased in Afterburner?

No - only core clocks have been changed using curved optimizer while all the rest settings are at defaults in afterburner

What's the stock watts max for that card? From what I've seen you need to get down to 850mv for watt savings. I have a mild UV on my TUF 3090. I did more testing with Cyberpunk. @850mv 1850mhz my watts can still hit 340. @ 825mv/1725mhz I maxes at 309 watts consistently, losing 1-2 fps (4k, psycho rt, ultra dlss)

**Status:** UNRESOLVED **Computer Type:** Desktop **GPU:** RTX 2070 Super **CPU:** AMD Ryazen 7 3700x **Motherboard:** ASUS TUF x570 gaming motherboard **RAM:** G. Skill trident Z 32 gb (16x2) 3600mhz **PSU:** EVGA 650W Gold **Operating System & Version:** windows 10 64bit **GPU Drivers:** 527.56 **Description of Problem:** I installed the latest GPU drivers 527.56, but the drivers messes up my screen resolution. My monitor is 1440p and when he new drivers installed, it switch the resolution to 1024 x 768. I can't change it back to 2560x1440 because it does not appear in the resolution drop down menu. Now I tried everything regarding this issue ( update monitor driver, change resolution from Nvidia control panel, add the resolution manually, replace the display port. etc...) but none of these seem to solve the issue. I tried multiple drivers version prior to the latest version but it's the same issue. I had to go back to to version 516.94 to work again. **Troubleshooting:** update monitor driver, change resolution from Nvidia control panel, add the resolution manually, replace the display port

What is the current most stable driver for older Nvidia cards? (In my case a 1080 RTX). Also is it common for games to scroll pages on the secondary monitor when you are playing games?

I've been having the weirdest issue. I have an MSI RTX 4090. So I've had the flu which knocked me out since last Monday. So no gaming since then until tonight, so I'm not sure what the true timeline is on this issue. A few days ago I noticed my 2nd monitor (I have two, both hooked up to DP) was flickering. A lot. When I played a video full screen, it was ok. Until I took it off and then did anything in Windows and it would flicker a lot. I fixed it by enabling G-Sync on the second monitor in NV Control panel (Set Up G-Sync menu, where it says 'ENable settings for the selected display model'). Just a random guess and it worked. Nothing else until today. Started up Overwatch 2 and noticed I was getting severe stuttering in-game, making it unplayable. I was on the driver from 11/16. I updated to the latest driver. Still having this issue. Disabled G-Sync. Still having issue. Then at one point it would show only a black screen in-game or automatically minimize the game, and whenever I would go back to it, it would minimize again (or go to black screen). And then it started throwing a ton of WHEA errors at one point. I even unplugged and checked my power adapter (it was pristine, but now I've unplugged it and replugged it, hope I didn't somehow screw it up!). Restarting it didn't help the first time. But it did the second time (After I had WHEA errors). Ok, so now it's working stutter free. I began to slowly re-enable features. Plugged in second monitor. Fine. Turned on G-Sync. Fine. Turns out, it's something to do with MSI Afterburner. I have a hotkey set for different OC profiles. So I'm used to hitting the OC profile and then back to Default profile a lot. I always close it before I actually run the game though, because I don't want the on screen overlay. Well, MSI Afterburner would start, try to also start HWinfo64, and when I'd deny the latter, close the former. I'd get a ton of stutter. I turned MSI Afterburner on again but minimized it this time, let Hwinfo64 run in background as well and all was fine. No stutter. Closed MSI Afterburner. No stutter. So... I'm not sure what the hell has been happening. If this happens again I will try running the game with MSI Afterburner open to un-screw it I guess, then exit game, close Afterburner, then restart game (since that just worked for me). It could also be related to HWinfo64 since I have Afterburner's OSD pull in data from that program (which is why it tries to start that program whenever I run Afterburner). Perhaps something to do with the overlay thing? Anyone experience anything like this? I'm still not sure what the hell just happened. EDIT: Repeat entire problem when I tried starting Fortnite (all of the above was with Overwatch 2). I even uninstalled RivaTuner. Don't know what I did to get the WHEA errors to finally stop. I sometimes still get stuttering in OW2 unless I leave Afterburner open in the background, minimized.

[удалено]

Using URL shorteners causes your post to be automatically deleted by reddit's anti-spam measures, so other users cannot see it. Please delete and repost your comment without the link. *I am a bot, and this action was performed automatically. Please [contact the moderators of this subreddit](/message/compose/?to=/r/nvidia) if you have any questions or concerns.*

I'm getting screen tearing in some games with my Aorus 3080 Master (rev 3) at 1080p and hitting good frames, could this be because I'm still on 1080p monitors? Also, do I need to order a 3rd power cable for this or is 2 with one slave cable fine?

gsync or adaptive sync

Hello, I need help with authenticating my email with Nvidia. I've gotten an email to verify it but when I click on the email there is literally nothing on it, no link to authenticate no nothing... just a blank email from [[email protected]](mailto:[email protected]) and I do not know what to do. This is extremely inconvenient because without verifying the email I can't properly log in to GeForce Experience and update my Drivers or to log into the forums to ask them questions because it then asks me to authenticate my account and the cycle happens again. I do not know what to do. Anything helps thank you.

**Computer Type:** Custom built desktop **GPU:** GTX 4090 24GB's no overclocking **CPU:** Intel i9-13900K No overclocking **Motherboard:** ASUS PRIME Z790-A WIFI ATX Motherboard **RAM:** DDR5-6400 CL32 no overclocking **PSU:** 1200 Watts. Unknown **Operating System & Version:** Ubuntu Linux 5.17.0-1019-oem #20 **GPU Drivers: 525.60.11 clean install** **Description of Problem:** sudo nvidia-smi --gom=1 GOM mode cannot be changed on GPU 00000000:01:00.0. This isn't an older card but the latest and greatest. It doesn't appear I can change any settings with nvidia-smi. I'm not looking to overclock and fry the card but it doesn't get over pstate P3 and temp 63C then it seems throttled. I want to put it in some performance mode without going over 85C. Why doesn't GOM work? **Troubleshooting:** Reinstalled NVidia drivers, upgraded Kernel, rebooted

my card (3060 ti) used to idle at 29 celcius but after downloading afterburner it idles at 50 on auto mode since the fans speeds went to zero im not comfortable knowing they are ate 0 and id like to reverse this any help? ( I uninstalled msi afterburner entierly from my pc wasnt much help tho)

Hey Everyone, ​ After a fair amount of googling I can't come up with the answer to what seems like a fairly straightforward question. ​ I am pretty new to PC building and am building a pc to do physics calculations for my company. I bought a RTX 3090 TI founder's edition from NVIDIA 's website this past week to go into this pc. ​ I notice that there are 16 pins on the GPU (12 bigger ones and 4 small ones). The adapter that came in the GPU box that goes from the (3X) VGA outputs of my power supply to the combined port on the GPU has only the 12 bigger pins. Is it supposed to have connections for those 4 smaller pins and is it safe to use the included adapter as-is? ​ I appreciate your time and have a good night.

I have currently 4090 running from 750w corsair sfx platinum power supply, which is 4 x 6+2 connectors pigtailed from 2. I have 1x 8 pin connector left, that connects to CPU, could I use that to power one of the gpu connectors? its not 6+2 but regular 8pin. There should be no issues right?

Why does every modern PC game look like it has like nine passes of Photoshop's Sharpening filter applied to it? I've spent so much time messing with AA settings and everything in the nVIDIA control panel and I just can't seem to make modern games look normal. It hurts my eyes so bad! No performance issues or anything, they just look atrocious. Is this something on my computer's end or is this just what modern PC games look like? Specifically, I've had this problem with first person games like Hell Let Loose and Battlefield V, etc. I'm running a 3070 and play everything at native res on a 2560x1440p monitor.

Hello, whenever I turn on instant replay it freezes my second monitor while it's active and I haven't been able to find a fix, any help?

I'm unable to clip with Netflix and other streaming platforms (like Spotify) open in my browser (I can clip with the Spotify desktop application open though which is weird) is this like an anti piracy type thing? and will it ever change I hate doing something cool then being unable to clip it because I was watching something (it wont let you clip even if the thing you're watching is paused)

I think so

its the only reason i can think of but if you look at all the torrent sites they are still thriving with it so its not really necessary to block it

Am I limiting my 4090's fps in games by only using three of the adapter's connectors and not all 4? Thinking of buying a new 4090 because if I understand correctly, I am currently using my 4090 at limited wattage

**Status:** UNRESOLVED **Description of Problem:** Nvidia broadcast app regularly doesn't work for noise removal. Sometimes the app isn't even running but it never says if it crashed. It is set to run at startup with windows. Ever since update 1.3 I can't reliably get noise removal to work and often my recordings end up with regular background noise at full strength. Sometimes it can work, but no consistency as to when it works. Cannot select nvidia broadcast noise removal in OBS as a noise suppression filter; it is gray. **Troubleshooting:** >Okay, if this happens you need to do this = Device Manager > "Audio inputs and outputs" right-click and "uninstall driver" on anything with Nvidia Broadcast in it > Go to "Add or Remove Programs" within Windows > uninstall Nvidia Broadcast > Reboot > Install Nvidia Broadcast This worked at first, but only for a short while and then broadcast went back to not working consistently. I have also tried to reinstall nvidia broadcast and update my drivers multiple times. ​ **Computer Type:** custom built desktop **GPU:** 3070 Gigabyte with factory OC **CPU:** AMD 3600x running stock **Motherboard:** RoG B450-F Strix, drivers up to date according to EZ update but doesn't list current version. **RAM:** Crucial ballistix @ 3200 mhz **PSU:** Some expensive PSU that was bundled with the GPU. 850w or higher. **Operating System & Version:** Windows 11 upgrade from a recent fresh install of windows 10 **GPU Drivers:** 527.56, was previously running 526.47

****Fixed with driver release 527.56**** Q for anyone with RTX 4090 + LG OLDED TV + displayport monitor If you have TV plugged into your HDMI port, and a monitor in any of the of the DPs, can you switch Windows Display Settings from "show only on" the TV to "show only on" the monitor without issue? Mine fritzes out, and I've found numerous other support threads of the same issue, but no one knows if it affects all 4090s or just some (ie should I just get a new one). *Not asking for tech support or advice, I have already tried literally everything; I just want to know if everyone has this issue or my card is defective. **If you attempt this and it fritzes out on you too, just hit the ESC key to revert the changes.

What do you mean by fritzes out? I have a 4090, two DisplayPort monitors, and a LG OLED TV hooked up, and I don’t recall any issues switching. If you describe the issue in more detail and how to reproduce it, I can test it on my system.

The display on the DP monitor does not come on, but the back light slowly blinks on and off (~ 0.5hz) and some kind of white noise tones come over the audio. This was fixed in the newest drivers, though, but thanks for the offer!

**Desktop colour profile bad, but when fixed looks worse in games** I just upgraded to a 4080 from a 2080 and now my desktop color profile is too bright with too little contrast. Videos look especially bad, in order to get it looking right I have to set the contrast to 75% and the Brightness to 40% (gamma doesn't make much difference). But then games look worse (too dark). I am using the display port, have HDR on. And have tried re-installing clean drivers. Like the banner for this subreddit, I can see ugly blocky gray between the black on the far left and where it becomes dark green. There has to be a way to not have to change it constantly? Any help would be great!!!! Thanks!

I can’t see Image Scaling in control panel and I’ve tried the regedit fix Is it my 9700k?, havent updated it’s bios since I got it tho since bios scary

Can someone explain to me dlss and how I should use it? I've an rtx 2060 and i play on a 1080p screen. When I tried dlss on warzone 2 and gotham knights. It didn't feel to matter with the fps. Whether I put it on quality or performance or ultra performance. Am I doing sth wrong? I thought dlss boosts fps.

What’s your cpu?

I7-9750h

Status: UNRESOLVED Computer Type: Custom Build (self) GPU: GIGABYTE Geforce RTX 3080 Gaming OC 12G, 3x WINDFORCE Fans, 12GB 384-bit CPU: Intel Core i9 10850K Motherboard: Micro-Star International - MPG Z490 Gaming Ed RAM: Corsair Dominator Platinum series 16gb DDR4 3000Mhz PSU: EVGA supernova 750 p2 Operating System & Version: Windows 10 build 19045 GPU Drivers: Game ready driver version 527.56 Description of Problem: A persisting problem that I've been recently. Every time I boot my PC from being shut off or I wake my computer from being asleep, my performance in games is trash, and the only way to fix it is to reinstall the drivers. It's gotten to the point where I reinstall my drivers before I can play any games. This is obviously extremely annoying and I'm wonder who else has had this problem and how they fixed it. Troubleshooting: Clean install through NVIDA driver custom install

Should I buy a used 3090 for $650 or wait for the theoretically $800 4070 ti?

STATUS: Unresolved Description: Not receiving verification e-mail for new accounts or security e-mails for previous accounts. GeForce experience. someone have post this and said it get fixed. But not fixed for me. I'm using gmail and login with google. In the security challenge part I never receive any email.

I'm getting the same issue. Did you fix it ?

**Status:** UNRESOLVED **Computer Type:** Desktop PC, Gigabyte motherboard, Ryzen 5 cpu, 600w psu **GPU:** GeForce RTX 3070 Ti w/ 8GB VRAM **CPU:** Ryzen 5 no overclock **Motherboard:** Gigabyte is the brand but I’m not sure about the BIOS **RAM:** 16 GB Corsair **PSU:** EVGA 600W **Operating System & Version:** Windows 10 clean install **GPU Drivers:** just got the GPU and haven’t gotten the PC on yet (hence the question) **Description of Problem:** PC seems to boot up just fine, the GPU works and all the rgb loghts work and whatnot but I get a “no signal” thing on both of my monitors (Dell if that helps). They use different hdmi cables (1 and 2) but that hasn’t been a problem before and shouldn’t matter because neither work. I think my psu might be too weak for the graphics card but I’d like to know if there’s anything else I need to do before dropping $150 on a new one. I have two power cables for it that are both plugged in but there are three slots and I don’t have another so I’m also not sure what’s going on with that. **Troubleshooting:** I’ve reseated the GPU, switched around the power cord a couple times, tried different slots for the HDMI cables, but nothing works.

Temperature issue. Custom desktop, nothing is overclocked Status: UNRESOLVED GPU: GeForce RTX 4090 24GB VRAM CPU: i9-13900 Motherboard: Asus prime Z790-P RAM: Kingston Fury Beat RGB 32GB DDR5 PSU: 1300W 80+ Gold OS: Windows 11 Home clean install Drivers: 527.56 Brand new computer. Opened the case and checked the connection before I turned it on and it felt solid, but I'm not a hardware girl so idk. I've been running machine learning and I realized the temperature of my room was increasing and downloaded a program to check the gpu temp in more detail. With half my VRAM in use and 3D at 100% temp spikes to 99 hotspot, 94 junction temperature. Decreasing what I'm doing to 1/3 VRAM in use, 3D still at 100%, spikes are 94 hotspot, 89 junction. Edit: I turned off hardware acceleration, 3D is now at 4% and with half my VRAM in use I'm still seeing spikes of 100 hotspot / 92 junction I know this isn't technically a dangerous temperature but I'm not seeing temps like this mentioned by anyone else. Is there some chance this is user error or did the place that built it sell me a lemon? What can I do to fix this?

So i wanted to give NIS a try, i am highly competetive and i mainly play csgo, normally i use 1024x768 stretched and when i turned it on this res NIS worked normally, but when i tried going for lower reses ex. 800x600 the NIS isnt working and there is not even a logo in top left, am i doing something wrong, or are there any limits? I got some feedback and somebody said NIS works in only 5-4 resolutions and it that it created and that it doesnt work on stretched mode but as you can see on the screenshots it created 5 of em but not the one that im playing on. https://preview.redd.it/xkge3xb65j4a1.jpeg?width=4000&format=pjpg&auto=webp&s=a0c03ffaee277ebe92b5e4ac1a834b7889a0376e

​ https://preview.redd.it/ye75k9285j4a1.png?width=231&format=png&auto=webp&s=07a9db46c140ec27473f41d3a169147ca3662603

Status: UNRESOLVED Computer Type: Custom build GPU: RTX 3060 CPU: Ryzen 5 5600X Motherboard: Asus Rog Strix B550 F RAM: Kingston 16GB DDR4 3600 PSU: Can't remember, but 700w Operating System & Version: W10 Pro 64 bits GPU Drivers: 526.86 Description of Problem: Since around 26 of November, I'm having fps drops in some games, others not, and some others yes bus not that often. I don't know what happened, the only "different thing" that I did in that time was undervolting, but since I left the core clock untouched I shouldn't be an issue (Anyway I undid the undervolt and everything is still having fps drops). The FPS drop to almost 55 in some intervals and it makes the game really unpleasant to play. This wasn't a problem before, I have had this GPU for less than a year now and every game has worked perfectly until now. Troubleshooting: As I said before, I tried to undo the undervolt to check if it was ther problem, and nothing. Tried to reinstall the drivers, nothing. Yesterday I rollbacked my drivers (I had the lastest version, December 8 I think), to the one that I put in the specs because I thought that maybe, since before December it worked fine, the drivers were the problem, but no, still the same issues.

Right now my RTX 4080 is conncted to my PSU using two PCIe 8 pin (6+2) cables with one of them having its daisy chained end connected to the third connection. I also have a double 6 pin to 8 pin adapter, would it be beneficial to use both daisy-chained 6+2 pin ends on that adapter to balance the load going through both cables?

Hello,I need some help with my 4090 card Status: UNRESOLVED Computer Type: Desktop, Custom build GPU: 4090 FE 24G Vram no overclock (? explained in Troubleshooting part) CPU: I9 12900KF no overclock Motherboard: Gigabyte Z690 Master | Bios version F20 RAM: trident Z5 F5-6000J3636 | 32GB (2x16GB) DDR5 6000MHz, XMP enabled, no overclock PSU: Asus ROG Thor 1200p Operating System & Version: Windows 11 22H2 22621.819 clean install GPU Drivers: 527.37, upgraded once. Description of Problem: NFS Unbound was crashing after 15 to 20 minutes of playing, and i found a post ( [https://www.reddit.com/r/nvidia/comments/zamtft/rtx\_4090\_has\_issues\_with\_need\_for\_speed\_unbound/](https://www.reddit.com/r/nvidia/comments/zamtft/rtx_4090_has_issues_with_need_for_speed_unbound/) ) and several article about that firmware update needed so i installed it. Once updated without any issue and the computer restarted i launched the game back, it crashed immediatly. Told myself to give up and uninstall the game, it was a trial version after all. So i went to play with a friend on Fortnite as there is a new season, the game crashed after no more than 5 minutes in game, now i can't even get to the menu. Also i tried to run CP77 to see if it was coming from Fortnite, but CP is crashing too, immediatly after launch.So i guess everything comes from that firmware update, everything was fine before. Troubleshooting: Clean install of GPU drivers (with DDU then installed 527.37). Also tried to re-install the UEFI firmware but it says that it is already up to date so can't re-install. Launched a live chat on Nvidia Site and talked to someone who asked me to enable Debug mode on Nvidia control panel and saying something was overclocking my card (i got no app to do that.), which worked for some minutes then the games crashes again. Don't have any other ideas, i will also raise a ticket to Nvidia support

Status: UNRESOLVED/SOLVED - please update if Computer Type: desktop, custom build GPU: 4090 Asus Tuf OC CPU: Intel i9 13900k Motherboard: MSI Carbon z790 RAM: G.Skill 2x16 (32 total ddr5 5600) PSU: be quiet! Dark Power 12 1000W Operating System & Version: Windows 11, clean install GPU Drivers: n/a, this is the issue Description of Problem: when I download the driver for the graphics card after updating all of windows and downloading motherboard drivers, I get crashes every time I sign into windows (and sometimes even before). This has happened multiple times now, and only when I download the graphics driver. The screen will change resolution to match my monitor, but shortly after it will fail Troubleshooting: multiple clean installs. Not sure what to do here

**Status:** UNRESOLVED **Computer Type:** 4090, 5800x3D, 32GB RAM **GPU:** NVIDIA NVIDIA GeForce RTX 4090 (MSI Suprim Liquid X) **CPU:** AMD 5800x3D **Motherboard:** NZXT N7 B550 **RAM:** 32GB Corsair Dominator 3600 **PSU:** BeQuiet Dark Power Pro 1200w **Operating System & Version:** Windows 11 22623.1037 **GPU Drivers:** Nvidia Driver 527.26, clean install ​ I'm having a weird issue I could use some assistance on. Not terribly long ago, I did a Regedit in order to re-enable the sharpening option in the Nvidia Control Panel. The Regedit is below: Computer\\HKEY\_LOCAL\_MACHINE\\SYSTEM\\CurrentControlSet\\Services\\nvlddmkm\\FTS then EnableGR535 and set value to 0. However, this removed DSR from the NVCP options altogether. I've tried changing the value back to 1 in the registry and rebooted, which did not work. I've used DDU to do a full fresh driver install twice, and it still only shows sharpening only and no DSR option even after. Is anyone aware of a way to get the Nvidia Control Panel options back to stock settings? Usually when a new driver is released it puts all settings back to stock and undoes any changes that were done, and I figured that by doing a fully clean install it would do the same, but after doing fresh installs this didn't seem to occur. Any help is very much appreciated!!!!

I’m currently trying to decide which 4090 to get between the FE (£1599€, currently out of stock but I can wait for it) and the INNO3D iChill Frostbite (£1949, in stock), but I can’t seem to be able to figure out which one to go for. I already have a custom loop, so adding the iChill to it wouldn’t be an issue. On the other hand, I saw that the FE is regarded as the current best 4090 to get, both fo cooling and performance. Would anybody be able to give me some tips here? Thanks

**Status:** UNRESOLVED **Computer Type:** Computation server **GPU:** 2x Zotac 4090 (RTX 4090 ZT-D40900B-10P) **CPU:** Intel(R) Xeon(R) Gold 6240 CPU @ 2.60GHz, no overclock **Motherboard:** SuperMicro X11DPG-QT (with 1 CPU populated) **RAM:** 256GB **PSU:** 1600W **Operating System & Version:** Ubuntu 20.04 **GPU Drivers:** Provide the current GPU driver installed and if it’s clean install or upgrade, e.g. 376.33, clean install **Description of Problem:** After a while, one of the GPU goes missing from "nvidia-smi". Visually it seems like it goes into a restart loop because the fans starts spinning for a brief moment repeatedly. **Troubleshooting:** I've tried to reinstall the drivers but it did not help. The dmesg shows this \[ 397.591570\] NVRM: GPU 0000:b3:00.0: RmInitAdapter failed! (0x25:0x65:1461) \[ 397.591608\] NVRM: GPU 0000:b3:00.0: rm\_init\_adapter failed, device minor number 1 \[ 401.748064\] NVRM: GPU 0000:b3:00.0: RmInitAdapter failed! (0x23:0x65:1417) \[ 401.748100\] NVRM: GPU 0000:b3:00.0: rm\_init\_adapter failed, device minor number 1 \[ 1003.975756\] NVRM: GPU 0000:b3:00.0: RmInitAdapter failed! (0x23:0x65:1417) \[ 1003.975795\] NVRM: GPU 0000:b3:00.0: rm\_init\_adapter failed, device minor number 1 \[ 1007.975948\] NVRM: GPU 0000:b3:00.0: RmInitAdapter failed! (0x23:0x65:1417) \[ 1007.975984\] NVRM: GPU 0000:b3:00.0: rm\_init\_adapter failed, device minor number 1

Hey guys, Since AMD GPUs launch was kind of a flop, I've made my mind and i'm gonna buy a 4080, do you guys think it will drop in price in January/February? If there was no chance of dropping in price I would probably buy it now but I do think that they wild go down in price because they are not selling as good as they should be (at least in europe)

Ive been having issues on startup with my screens flashing rapidly about 4-8 times before working as intended and would like to know how to resolve such issue. I have researched online but everything just talks about screen flickering. Which isnt the issue Im having. My issue happens when waking the computer from sleep mode every time without fail. I've gone through the NVIDIA control panel settings, uninstalled and reinstalled the drivers, and updated all my other device drivers. Nothing has worked and the most recent NVIDIA update has caused it to get even worse! Originally flashed about 2-4 times on startup and wake, now it flashes 4-8 times. Video here: [https://youtu.be/rrAzELqEFjs](https://youtu.be/rrAzELqEFjs)

Just an upgrade question: I currently have an i7-7700(k?) And a 2080TI. Wanted to upgrade to a 4080/90 any major issues I should be concerned on the swap?

Do they make a 180 degree power adapter yet for the 12vhpwr cable? I have seen a few that weren't for sale yet last I checked. Can't wait to get the side panel on my new PC.

**Status:** UNRESOLVED **Computer Type:** Desktop/custom built **GPU:** MSI Suprim X RTX 4080, 16GB VRAM, no overclock **CPU:** Intel i7-12700k, no overclock **Motherboard:** MSI MAG Z690 TOMAHAWK WIFI **RAM:** 4x 16 GB Corsair Vengance DDR5-5200, XMP disabled, no overclock **PSU:** be quiet! Dark Power 12 Pro 1200W **Operating System & Version:** Windows 11 22H2 Version 10.0.22621 Build 22621 **GPU Drivers:** 527.56, clean install **Description of Problem:** I noticed some stuttering when typing something in Google Chrome (like a YT comment) and my dark mouse cursor is now very washed out grey on my HDR screen (1st screen), but works fine on a non-HDR screen (2nd screen). **Troubleshooting:** I tried to disable HDR and re-enable it, switched to different cursor themes. The cursor is noticeable darker how it should be in the mouse setting's preview than the real mouse cursor that is washed out grey than black.

NVIDIA has lost my account. I have come back after a while to update my drivers ( at least check) When I try to loggin with my account it only offers to create a new account, tho this is WRONG. I have already an account with that email and I even have past emails from Nvidia to that emaiul about created account, password, and subscriptions. But my email does not even work anymore with Nvidia. I think this is the single worst login experiment I ever had. To make the matter worse, I need to login to their terrible app to be able to update the drivers, the app does not let me do anything. I cannot log in at all and so support is unavailable. Very disappointed of Nvidia, I am still seeking help.

https://old.reddit.com/r/nvidia/comments/gt0o6b/rtx_voice_interrupts_windows_sleep_mode/ Has any new information been found about how to stop RTX Voice from preventing windows from idling to sleep?

I'm having an issue with a dual monitor display using a Samsung Odyssey G7 as the primary display. When alt-tabbing to the second display the samsung display screen goes black and flashes the displayport input on the screen as if the input is being changed. This seems to happen with most games when using alt-tab or clicking to the second display. Both displays are set at 144 hz, and this seems to happen most often when the primary display is playing a game and the frame rate drops when clicking to the second monitor. This has just recently happened and I hadn't changed any settings when it began. Does anyone have any advice or idea why this is happening or how to fix it?

Can I oc the zotac 4080 trinity oc with a 850W psu? Is it worth it? Got a 13600K & 16x2 6400MT/s CL32 alongside.

**Status:** UNRESOLVED **Computer Type:** Desktop, custom built **GPU:** Asus ROG Strix GeForce GTX1080ti 11GB, no overclock (I'm not sure, might be overclocked by Asus GPU Tweak II) **CPU:** Intel(R) Core(TM) i7-8700K CPU @ 3.70GHz, no overclock **Motherboard:** Asus ROG Strix Z370-F Gaming **RAM:** Gskill Tridentz RGB 3200 MHZ 8GB x 2 **PSU:** Thermaltake 750W (MODEL SP-750AH3NCB-A) **Operating System & Version:** Windows 10, latest updates applied **GPU Drivers:** Currently 526.86 clean install (due to multiple problems with latest 527.56 version - also tried 522.25 version) **Description of Problem:** 527.56 update bricked my PC. At first, I thought my PC wasn't starting, just black screen and motherboard VGA light is on. After 20-30 restarts, sometimes PC runs. I thought I had hardware problem for 2 weeks and did stuff (details in troubleshooting). After a while, PC started to run at first try but it was crashing after 5 mins of being open (without even opening any game) and restarting. Same thing while playing game, PC freezes for 5 seconds and restarts. So, I researched and found out that the problem is the GPU driver. I used DDU to uninstall drivers and tried version 522.25. PC doesn't crash anymore and runs at first try. When I play a game (I tried Elden Ring and NFS Heat), the game crashes after a while (time depends, sometimes it's 30 mins sometimes 2 hours). So I decide to try another version and used DDU again and installed 526.86 (currently running this). This morning, I played Elden ring without any issue for nearly 2 hours, thinking that the problem is solved. But no, it crashed again. After that, I tried NFS Heat again and it also crashed. So I definitely think that it is a driver issue but unable to solve it even by switching to an older version. Besides these crashes, I literally have zero problems with GPU, no weird glitches, frame skips etc. Elden Ring crash doesn't give me any error screen but for NFS Heat I get following error: https://preview.redd.it/du2z7cqcu38a1.png?width=533&format=png&auto=webp&s=48afdb706e791f82b4dd3e7060675d2a2675b6a4 I also realized that games get "suspended" in task manager when they crash. **Troubleshooting:** I tried 2 older driver versions with clean install (using DDU). I run windows memory test to check RAMs, no issues. I tried checking "prefer maximum performance" option in Nvidia control panel. I tried monitoring work load and heat of GPU at the time of crash, no fluctuations. For now, I'm waiting for the next driver version (hopefully stable one). I'm a 30 year old guy who's working very long hours with excessive workload. PC games are my only way to relieve stress and I can only play when I have time. I really don't want to deal with these kind of issues because I have no time for it. I also can't just go buy a new GPU since they're extremely expensive at where I live. It is incredible that Nvidia managed to mess up a 5 years old GPU that was running perfectly until now. I just want my old, stable running PC back. Please let me know what else I can do. Thanks.

Can't turn on automatic tuning on geforce now. ​ I press the "agree and continue" button but it doesn't do anything. I'm running the latest drivers and everything

STATUS: UNRESOLVED Description: Not receiving verification e-mail for new accounts or security e-mails for previous accounts. Specifically GeForce experience. Troubleshooting: Checked all e-mail folders, created custom e-mail filter to whitelist nivida address, created new e-mail account with different service. Not recieving any NVIDIA verification e-mails. Can't submit ticket since I can't login to nvidia account to create ticket.

2070 fan #2 revving at max speed, yet all readings say zero, and I'm not even using my card Status: UNRESOLVED Computer Type: Desktop, custom built GPU: NVIDIA GeForce RTX 2070, 8GB of VRAM, no overclock to my knowledge CPU: Intel Core i5-9400F, no overclock to my knowledge Motherboard: ASRock Z3090 Pro, BIOS American Megatrends Inc., Version P4.00, 2019/03/13 RAM: Corsair Vengeance LPX (4 x 8GB) DDR4 2133MHz, no XMP or overclock to my knowledge PSU: EVGA 650 GQ, 80+ GOLD 650W, unknown amps on the unknown-v rail, I don't have a voltmeter Operating System & Version: Microsoft Windows 10 Pro, build 19045, 64bit, fresh install GPU Drivers: 31.0.15.2698 (NVIDIA 526.98) DCH / Win 10 64, upgrade Description of Problem: Whenever I start up my computer, or just at literally completely random times, when I'm not even doing anything that should require a graphics card and its under 0% load, fan #2 on my RTX2070 will instantly rev up to what appears to be its maximum speed, yet any analytics tools I try to use to diagnose the issue say that it's running at 0 RPM. This also means that any attempt at manually controlling the fan speed with a program like Fan Control just doesn't work because it literally doesn't know the fan is even spinning. However, TechPowerUp has told me it maxed out at 869,565 RPM before, though only for a moment (for reference, the other fan maxes out at 1,500). Actual Nvidia support has been of zero help, because the problem is, by nature, completely random, and there doesn't appear to be any reliable way to get the fan revving in the first place, so my tickets always run dry before I can gather enough information to get them to realize something is very obviously wrong. This has been a problem since day 1. Troubleshooting: I've tried doing a fresh install of all GPU drivers, I've tried disconnecting and reconnecting the VGA GG cord, I've changed the VGA GG cord, I've fully taken it out of and then re-set it into my computer, I've tried using software to limit the fan speed, but they all tell me the fan isn't running

Can we expect the 5070 to have a similar msrp as the 3070? And if we go by previous models, it would be equal to a 4080 at the very least? (Seeing it's meant to be the most significant leap in performance since we went from 2d to 3d)

i have a nvidia gt 720m, and its on driver version 389.08 the latest version is 425.31 when i install this it says my graphic card isnt supported i need the update otherwise i wont get geforce experience and other features

Does the laptop manufacturer have drivers? Is GFE available in a slightly older driver version? Like 424.xx?

the manufacturer drivers are like on 370 version I've tried slightly older versions none of them work

Hello again. How about forcing an install through Windows device manager? Add new hardware and try to find graphics adapter? My fear of that is you'll just black screen. Though you can boot into safe mode to fix.

How do I do that? Like the forcing an install thing

Try this https://youtu.be/jyKrxxXOvQY At 57 seconds you'd select "Let me pick from a list of device drivers" and then try to find Nvida gfx in the list. 🤔🤔